Sigma marine paints

Sigmacover 280 Sigma Marine paint

Name: Sigmacover 280 Sigma Marine paint
Brand: Sigma marine paints
SKU: Sigma-Cover-280
Availability: InStock
Rating: 5 (17 reviews)

(17 reviews) Write a Review

SKU:: Sigma-Cover-280
UPC:
MPN:
Weight:: 18.00 KGS
Shipping:: Calculated at Checkout

₦0.00

Current Stock:

Quantity:

Description

Description

Sigmacover 280 Sigma Marine paint

GZ Industrial Supplies Limited is a distributor of Sigma marine coatings in Nigeria Our Sigmacover 280 sigma marine paint is a universal epoxy primer system used for such places as ballast tanks, decks, topsides, superstructure, hull and cargo oil tanks.

Characteristics of Sigmacover 280 Sigma Marine paint

Universal epoxy primer system suitable for Ballast Tanks, Decks, Topside, Superstructure, Hull and Cargo Oil Tanks
General-purpose epoxy primer in protective coating systems for steel and non-ferrous metals
Good adhesion to steel and galvanized steel
Good adhesion to non-ferrous metals
Good flow and wetting properties
Good water and corrosion resistance
Cures at temperatures down to 5°C (41°F)
Suitable for touching up of weld seams and damages of epoxy coatings during construction
Excellent recoatability
Can be overcoated with most alkyd-, chlorinated rubber-, vinyl-, epoxy- and two-component polyurethane coatings
Suitable on wet blast cleaned substrates (damp or dry)
Compatible with well-designed cathodic protection systems

RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES

Immersion exposure

Steel or steel with not approved zinc silicate shop primer; blast cleaned (dry or wet) to ISO-Sa21⁄2, blasting profile 30 - 75 μm (1.2 – 3.0 mils)
Steel with approved zinc silicate shop primer; weld seams and areas of damaged shop primer or breakdown should be blast cleaned to ISO-Sa21⁄2, blasting profile 30 - 75 μm (1.2 – 3.0 mils) or power tool cleaned to SPSS-Pt3
Coated steel; hydrojetted to VIS WJ2L (blasting profile 30 – 75 μm (1.2 – 3.0 mils))
IMO-MSC.215(82) requirements for water ballast tanks
Steel; ISO 8501-3: 2006 grade P2, with all edges treated to a rounded radius of minimum 2 mm (0.0789 in) or subject to three pass grinding
Steel or steel with not approved zinc silicate shop primer; blast cleaned to ISO -Sa21⁄2, blasting profile 30 – 75 μm (1.2 – 3.0 mils)
Steel with approved zinc silicate shop primer; weld seams and areas of shop primer damage or break down should be blast cleaned to Iso-Sa 21⁄2 blasting profile 30 – 75 μm (1.2 – 3.0 mils): [1] For shop primer with IMO type approval; no additional requirements; [2] For shop primer without IMO type approval; blast cleaned to ISO-Sa2 removing at least 70% of intact shop primer, blasting profile 30 – 75 μm (1.2 – 3.0 mils)
Dust quantity rating "1 for dust size class "3", "4" or "5", lower dust size classes to be removed if visible on the surface to be coated without magnification (ISO 8502-3:1992)
Atmospheric exposure conditions
Steel blast cleaned to ISO-Sa21⁄2, blasting profile 30 - 75 μm (1.2 – 3.0 mils) or according to ISO-St3
Shop primed steel; pretreated to SPSS-Pt3
Galvanized steel must be sweep blasted or otherwise roughened
Galvanized steel must be free from grease, salts and any contamination
Concrete / Masonry
Remove grease, oil and other penetrating contaminants according to ASTM D4258
Abrade the surface per ASTM D4259 to remove all chalk and surface glaze or laitance. Achieve surface profile - ICRI CSP
3 to 5
AMERCOAT 114 A may be used as a pit filler for certain applications. Check with PPG Technical Service for guidance on
chemical resistance
Maximum recommended moisture transmission rate is 3 lbs / 1,000 ft2 / 24 hours by moisture transmission test (ASTM
F1869, calcium chloride test or by ASTM D4263, plastic sheet test)
Alternatively, ASTM D4944 (Calcium Carbide Gas method) can be used, moisture content should not exceed 4%

Substrate temperature and application conditions

Substrate temperature during application and curing should be above 5°C (41°F)
Substrate temperature during application and curing should be at least 3°C (5°F) above dew point
Relative humidity during application and curing should not exceed 85%

INSTRUCTIONS FOR USE

Mixing ratio by volume: base to hardener 80:20 (4:1)

The temperature of the mixed base and hardener should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity
Adding too much thinner results in reduced sag resistance and slower cure
Thinner should be added after mixing the components

Product Data

Frequently Asked Questions

1. How long does marine paint take to dry?

Drying times can vary depending on the type of paint, environmental conditions, and the thickness of the applied coat. Typically, marine paint may take a few hours to dry to touch, but it may take several days for a full cure. Refer to the paint manufacturer's guidelines for specific drying times.

2. Can I apply antifouling paint over old antifouling paint?

In most cases, yes, antifouling paint can be applied over old antifouling paint. However, proper surface preparation is essential to ensure good adhesion. It's recommended to consult the paint manufacturer's instructions for specific guidance.

3.Can I paint my boat in any weather conditions?

Weather conditions can significantly affect the paint application and drying process. It's generally recommended to paint in dry, well-ventilated conditions with moderate temperatures. Avoid painting in direct sunlight, high humidity, or during windy or rainy conditions.

HOW TO USE MARINE PAINTS

MARINE PAINTS FOR BOAT DECK

IS ALL MARINE PAINT OIL BASED?

View AllClose

17 Reviews

17 Reviews

5
dependable

Posted by peter efi on Nov 14, 2023

As a happy customer, I have to admit that the longevity and protection of this maritime paint exceeded my expectations. This maritime paint works well and is reasonably priced. It is simple to roll and brush on, making work less laborious.
5
Excellent

Posted by Merit Johnson on Nov 01, 2023

This Paint is superb very reliable has high quality it texture is second to none. i recommend it.
5
SIGMACOVER 280 SIGMA MARINE PAINT

Posted by Udoma Effieong on Nov 01, 2023

To me this product deserve a Five star rating, the very best, it last long, dry fast and no choking smell. i came across it 4 years ago.
5
High Quality

Posted by Paul Udoka on Nov 01, 2023

The best product i have seen so far. very dependable and high durability Marine paint i started using it since 2019 .
5
best customer service

Posted by jason on Oct 25, 2023

I bought this sigma-cover from GZ, and it was delivered swiftly, Their customer service is the best
5
highly recommended

Posted by Issac on Oct 25, 2023

Its exceptional adhesion ensures a consistent, long-lasting finish and minimizes concerns about flaking or breakdown. Because of this paint's consistent and long-lasting performance, I highly recommend it.
5
wonderful

Posted by Happiness on Jul 03, 2023

I've tried several marine paints before, but this one stands out. It offers superior adhesion and durability, withstanding the harsh marine environment effortlessly. The color remains vibrant even after a while since i applied it. Awesome product
5
nice product

Posted by George on Jul 03, 2023

As someone who has worked extensively with maritime paints, I can confidently say that this paint excels in adhering to various surfaces like fiberglass, metal, and wood. Its exceptional adhesion ensures a uniform and long-lasting finish, eliminating concerns of flaking or delamination. I highly recommend this paint for its reliable and durable performance.
5
SIGMACOVER 280 SIGMA MARINE PAINT

Posted by Onyi Ogu on Jun 03, 2022

SIGMACOVER 280 SIGMA MARINE PAINT has a good adhesion on steel and non ferrous metals. Highly recommended for use even with good corrosion resistance